#include "SWM221.h"

void SerialInit(void);

int main(void)
{
	ADC_InitStructure ADC_initStruct;
	ADC_SEQ_InitStructure ADC_SEQ_initStruct;
	
	SystemInit();
	
	SerialInit();
	
	PORT_Init(PORTA, PIN14, PORTA_PIN14_ADC0_CH0, 0);		//PA.14 => ADC0.CH0
	PORT_Init(PORTA, PIN11, PORTA_PIN11_ADC0_CH1, 0);		//PA.11 => ADC0.CH1，注意：此通道只在 ADC 参考源为 ADC_REF_VDD 时可用
	PORT_Init(PORTA, PIN8,  PORTA_PIN8_ADC0_CH2,  0);		//PA.8  => ADC0.CH2
	PORT_Init(PORTB, PIN6,  PORTB_PIN6_ADC0_CH5,  0);		//PB.6  => ADC0.CH5
	PORT_Init(PORTB, PIN5,  PORTB_PIN5_ADC0_CH6,  0);		//PB.5  => ADC0.CH6
	PORT_Init(PORTB, PIN4,  PORTB_PIN4_ADC0_CH7,  0);		//PB.4  => ADC0.CH7
	PORT_Init(PORTB, PIN2,  PORTB_PIN2_ADC0_CH8,  0);		//PB.2  => ADC0.CH8
	
	ADC_initStruct.clkdiv = 4;
	ADC_initStruct.refsrc = ADC_REF_VDD;
	ADC_initStruct.samplAvg = ADC_AVG_SAMPLE1;
	ADC_Init(ADC0, &ADC_initStruct);
	
	ADC_SEQ_initStruct.trig_src = ADC_TRIGGER_TIMER1;
	ADC_SEQ_initStruct.samp_tim = 6;
	ADC_SEQ_initStruct.conv_cnt = 1;
	ADC_SEQ_initStruct.EOCIntEn = 0;
	ADC_SEQ_initStruct.channels = (uint8_t []){ ADC_CH0, 0xF };
	ADC_SEQ_Init(ADC0, ADC_SEQ0, &ADC_SEQ_initStruct);
	
	ADC_Open(ADC0);
	
	TIMR_Init(TIMR1, TIMR_MODE_TIMER, CyclesPerUs, 2000, 0);	// 500Hz
	TIMR_Start(TIMR1);
	
	while(1==1)
	{
		while(ADC_DataAvailable(ADC0, ADC_CH0) == 0) __NOP();
		printf("%4d,", ADC_Read(ADC0, ADC_CH0));
	}
}


void SerialInit(void)
{
	UART_InitStructure UART_initStruct;
	
	PORT_Init(PORTA, PIN0, PORTA_PIN0_UART0_RX, 1);	//GPIOA.0配置为UART0 RXD
	PORT_Init(PORTA, PIN1, PORTA_PIN1_UART0_TX, 0);	//GPIOA.1配置为UART0 TXD
 	
 	UART_initStruct.Baudrate = 57600;
	UART_initStruct.DataBits = UART_DATA_8BIT;
	UART_initStruct.Parity = UART_PARITY_NONE;
	UART_initStruct.StopBits = UART_STOP_1BIT;
	UART_initStruct.RXThreshold = 3;
	UART_initStruct.RXThresholdIEn = 0;
	UART_initStruct.TXThreshold = 3;
	UART_initStruct.TXThresholdIEn = 0;
	UART_initStruct.TimeoutTime = 10;
	UART_initStruct.TimeoutIEn = 0;
 	UART_Init(UART0, &UART_initStruct);
	UART_Open(UART0);
}

/****************************************************************************************************************************************** 
* 函数名称: fputc()
* 功能说明: printf()使用此函数完成实际的串口打印动作
* 输    入: int ch		要打印的字符
*			FILE *f		文件句柄
* 输    出: 无
* 注意事项: 无
******************************************************************************************************************************************/
int fputc(int ch, FILE *f)
{
	UART_WriteByte(UART0, ch);
	
	while(UART_IsTXBusy(UART0));
 	
	return ch;
}