|
|
#include "SWM221.h"
|
|
|
|
|
|
|
|
|
#define ADC_USE_INT 0
|
|
|
|
|
|
|
|
|
void SerialInit(void);
|
|
|
|
|
|
int main(void)
|
|
|
{
|
|
|
ADC_InitStructure ADC_initStruct;
|
|
|
ADC_SEQ_InitStructure ADC_SEQ_initStruct;
|
|
|
|
|
|
SystemInit();
|
|
|
|
|
|
SerialInit();
|
|
|
|
|
|
PORT_Init(PORTA, PIN14, PORTA_PIN14_ADC0_CH0, 0); //PA.14 => ADC0.CH0
|
|
|
PORT_Init(PORTA, PIN11, PORTA_PIN11_ADC0_CH1, 0); //PA.11 => ADC0.CH1，注意：此通道只在 ADC 参考源为 ADC_REF_VDD 时可用
|
|
|
PORT_Init(PORTA, PIN8, PORTA_PIN8_ADC0_CH2, 0); //PA.8 => ADC0.CH2
|
|
|
PORT_Init(PORTB, PIN6, PORTB_PIN6_ADC0_CH5, 0); //PB.6 => ADC0.CH5
|
|
|
PORT_Init(PORTB, PIN5, PORTB_PIN5_ADC0_CH6, 0); //PB.5 => ADC0.CH6
|
|
|
PORT_Init(PORTB, PIN4, PORTB_PIN4_ADC0_CH7, 0); //PB.4 => ADC0.CH7
|
|
|
PORT_Init(PORTB, PIN2, PORTB_PIN2_ADC0_CH8, 0); //PB.2 => ADC0.CH8
|
|
|
|
|
|
ADC_initStruct.clkdiv = 4;
|
|
|
ADC_initStruct.refsrc = ADC_REF_VDD;
|
|
|
ADC_initStruct.samplAvg = ADC_AVG_SAMPLE1;
|
|
|
ADC_Init(ADC0, &ADC_initStruct);
|
|
|
|
|
|
ADC_SEQ_initStruct.trig_src = ADC_TRIGGER_SW;
|
|
|
ADC_SEQ_initStruct.samp_tim = 6;
|
|
|
ADC_SEQ_initStruct.conv_cnt = 1;
|
|
|
ADC_SEQ_initStruct.EOCIntEn = ADC_USE_INT;
|
|
|
ADC_SEQ_initStruct.channels = (uint8_t []){ ADC_CH0, 0xF };
|
|
|
ADC_SEQ_Init(ADC0, ADC_SEQ0, &ADC_SEQ_initStruct);
|
|
|
|
|
|
ADC_Open(ADC0);
|
|
|
|
|
|
#if ADC_USE_INT
|
|
|
ADC_Start(ADC_SEQ0, 0);
|
|
|
|
|
|
while(1==1)
|
|
|
{
|
|
|
}
|
|
|
#else
|
|
|
while(1==1)
|
|
|
{
|
|
|
ADC_Start(ADC_SEQ0, 0);
|
|
|
while(ADC_Busy(ADC0)) __NOP();
|
|
|
printf("%4d,", ADC_Read(ADC0, ADC_CH0));
|
|
|
}
|
|
|
#endif
|
|
|
}
|
|
|
|
|
|
|
|
|
void ADC_Handler(void)
|
|
|
{
|
|
|
if(ADC_INTStat(ADC0, ADC_SEQ0, ADC_IT_EOC))
|
|
|
{
|
|
|
ADC_INTClr(ADC0, ADC_SEQ0, ADC_IT_EOC);
|
|
|
|
|
|
printf("%4d,", ADC_Read(ADC0, ADC_CH0));
|
|
|
|
|
|
ADC_Start(ADC_SEQ0, 0);
|
|
|
}
|
|
|
}
|
|
|
|
|
|
|
|
|
void SerialInit(void)
|
|
|
{
|
|
|
UART_InitStructure UART_initStruct;
|
|
|
|
|
|
PORT_Init(PORTA, PIN0, PORTA_PIN0_UART0_RX, 1); //GPIOA.0配置为UART0 RXD
|
|
|
PORT_Init(PORTA, PIN1, PORTA_PIN1_UART0_TX, 0); //GPIOA.1配置为UART0 TXD
|
|
|
|
|
|
UART_initStruct.Baudrate = 57600;
|
|
|
UART_initStruct.DataBits = UART_DATA_8BIT;
|
|
|
UART_initStruct.Parity = UART_PARITY_NONE;
|
|
|
UART_initStruct.StopBits = UART_STOP_1BIT;
|
|
|
UART_initStruct.RXThreshold = 3;
|
|
|
UART_initStruct.RXThresholdIEn = 0;
|
|
|
UART_initStruct.TXThreshold = 3;
|
|
|
UART_initStruct.TXThresholdIEn = 0;
|
|
|
UART_initStruct.TimeoutTime = 10;
|
|
|
UART_initStruct.TimeoutIEn = 0;
|
|
|
UART_Init(UART0, &UART_initStruct);
|
|
|
UART_Open(UART0);
|
|
|
}
|
|
|
|
|
|
/******************************************************************************************************************************************
|
|
|
* 函数名称: fputc()
|
|
|
* 功能说明: printf()使用此函数完成实际的串口打印动作
|
|
|
* 输 入: int ch 要打印的字符
|
|
|
* FILE *f 文件句柄
|
|
|
* 输 出: 无
|
|
|
* 注意事项: 无
|
|
|
******************************************************************************************************************************************/
|
|
|
int fputc(int ch, FILE *f)
|
|
|
{
|
|
|
UART_WriteByte(UART0, ch);
|
|
|
|
|
|
while(UART_IsTXBusy(UART0));
|
|
|
|
|
|
return ch;
|
|
|
}
|