|
|
#include "SWM221.h"
|
|
|
|
|
|
/* 注意：main.c中的main()函数必须在RAM中执行，因为其中会REMAP操作，代码所在Flash可能会被重映射到其他地址
|
|
|
*/
|
|
|
|
|
|
|
|
|
#define EEPROM_ADDR 0x7000
|
|
|
|
|
|
uint32_t WrBuff[20] = {0x14141414, 0x15151515, 0x16161616, 0x17171717, 0x18181818,
|
|
|
0x19191919, 0x1A1A1A1A, 0x1B1B1B1B, 0x1C1C1C1C, 0x1D1D1D1D,
|
|
|
0x1E1E1E1E, 0x1F1F1F1F, 0x20202020, 0x21212121, 0x22222222,
|
|
|
0x23232323, 0x24242424, 0x25252525, 0x26262626, 0x27272727};
|
|
|
uint32_t RdBuff[20];
|
|
|
|
|
|
void SerialInit(void);
|
|
|
|
|
|
int main(void)
|
|
|
{
|
|
|
uint32_t i;
|
|
|
|
|
|
SystemInit();
|
|
|
|
|
|
SerialInit();
|
|
|
|
|
|
|
|
|
printf("\r\nAfter Erase: \r\n");
|
|
|
|
|
|
FLASH_Erase(EEPROM_ADDR);
|
|
|
|
|
|
/* 将EEPROM_ADDR处的Flash映射到0地址，然后从0地址读取数据 */
|
|
|
FMC->REMAP = (1 << FMC_REMAP_ON_Pos) | ((EEPROM_ADDR/0x800) << FMC_REMAP_OFFSET_Pos);
|
|
|
FMC->CACHE |= FMC_CACHE_CCLR_Msk;
|
|
|
|
|
|
for(i = 0; i < 20; i++) RdBuff[i] = ((volatile uint32_t *)0x00)[i];
|
|
|
FMC->REMAP = (0 << FMC_REMAP_ON_Pos);
|
|
|
FMC->CACHE |= FMC_CACHE_CCLR_Msk;
|
|
|
|
|
|
for(i = 0; i < 20; i++) printf("0x%08X, ", RdBuff[i]);
|
|
|
|
|
|
|
|
|
printf("\r\nAfter Write: \r\n");
|
|
|
|
|
|
FLASH_Write(EEPROM_ADDR, WrBuff, 20);
|
|
|
|
|
|
/* 将EEPROM_ADDR处的Flash映射到0地址，然后从0地址读取数据 */
|
|
|
FMC->REMAP = (1 << FMC_REMAP_ON_Pos) | ((EEPROM_ADDR/0x800) << FMC_REMAP_OFFSET_Pos);
|
|
|
FMC->CACHE |= FMC_CACHE_CCLR_Msk;
|
|
|
|
|
|
for(i = 0; i < 20; i++) RdBuff[i] = ((volatile uint32_t *)0x00)[i];
|
|
|
FMC->REMAP = (0 << FMC_REMAP_ON_Pos);
|
|
|
FMC->CACHE |= FMC_CACHE_CCLR_Msk;
|
|
|
|
|
|
for(i = 0; i < 20; i++) printf("0x%08X, ", RdBuff[i]);
|
|
|
|
|
|
while(1==1)
|
|
|
{
|
|
|
}
|
|
|
}
|
|
|
|
|
|
|
|
|
void SerialInit(void)
|
|
|
{
|
|
|
UART_InitStructure UART_initStruct;
|
|
|
|
|
|
PORT_Init(PORTA, PIN0, PORTA_PIN0_UART0_RX, 1); //GPIOA.0配置为UART0 RXD
|
|
|
PORT_Init(PORTA, PIN1, PORTA_PIN1_UART0_TX, 0); //GPIOA.1配置为UART0 TXD
|
|
|
|
|
|
UART_initStruct.Baudrate = 57600;
|
|
|
UART_initStruct.DataBits = UART_DATA_8BIT;
|
|
|
UART_initStruct.Parity = UART_PARITY_NONE;
|
|
|
UART_initStruct.StopBits = UART_STOP_1BIT;
|
|
|
UART_initStruct.RXThreshold = 3;
|
|
|
UART_initStruct.RXThresholdIEn = 0;
|
|
|
UART_initStruct.TXThreshold = 3;
|
|
|
UART_initStruct.TXThresholdIEn = 0;
|
|
|
UART_initStruct.TimeoutTime = 10;
|
|
|
UART_initStruct.TimeoutIEn = 0;
|
|
|
UART_Init(UART0, &UART_initStruct);
|
|
|
UART_Open(UART0);
|
|
|
}
|
|
|
|
|
|
/******************************************************************************************************************************************
|
|
|
* 函数名称: fputc()
|
|
|
* 功能说明: printf()使用此函数完成实际的串口打印动作
|
|
|
* 输 入: int ch 要打印的字符
|
|
|
* FILE *f 文件句柄
|
|
|
* 输 出: 无
|
|
|
* 注意事项: 无
|
|
|
******************************************************************************************************************************************/
|
|
|
int fputc(int ch, FILE *f)
|
|
|
{
|
|
|
UART_WriteByte(UART0, ch);
|
|
|
|
|
|
while(UART_IsTXBusy(UART0));
|
|
|
|
|
|
return ch;
|
|
|
}
|