You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
145 lines
3.6 KiB
C
145 lines
3.6 KiB
C
#include "SWM221.h"
|
|
|
|
#define LIN_ID_Sensor 0x11 // 此从机是一个传感器，只能从它读数据
|
|
#define LIN_ID_Switch 0x21 // 此从机是一个开关， 只能向它写数据
|
|
|
|
#define LIN_NB_Sensor 6 // Number of Byte, 传感器的数据是 6 字节
|
|
#define LIN_NB_Switch 4
|
|
|
|
uint8_t Buffer_Sensor[LIN_NB_Sensor] = { 0x12, 0x34, 0x56, 0x78, 0x55, 0xAA };
|
|
uint8_t Buffer_Switch[LIN_NB_Switch] = { 0 };
|
|
volatile uint32_t Index_Sensor = 0;
|
|
volatile uint32_t Index_Switch = 0;
|
|
|
|
void SerialInit(void);
|
|
|
|
int main(void)
|
|
{
|
|
SystemInit();
|
|
|
|
SerialInit();
|
|
|
|
USART_InitStructure USART_initStruct;
|
|
|
|
PORT_Init(PORTA, PIN2, PORTA_PIN2_USART0_TX, 0);
|
|
PORT_Init(PORTA, PIN3, PORTA_PIN3_USART0_RX, 1);
|
|
|
|
USART_initStruct.Baudrate = 9600;
|
|
USART_initStruct.DataBits = USART_DATA_8BIT;
|
|
USART_initStruct.Parity = USART_PARITY_NONE;
|
|
USART_initStruct.StopBits = USART_STOP_1BIT;
|
|
USART_initStruct.RXReadyIEn = 1;
|
|
USART_initStruct.TXReadyIEn = 0;
|
|
USART_initStruct.TimeoutIEn = 0;
|
|
USART_Init(USART0, &USART_initStruct);
|
|
USART_Open(USART0);
|
|
|
|
USART_LINConfig(USART0, USART_LIN_SLAVE, USART_CHECKSUM_LIN13, USART_IT_LIN_ID | USART_IT_LIN_DONE);
|
|
|
|
while(1==1)
|
|
{
|
|
if(Index_Switch == LIN_NB_Switch)
|
|
{
|
|
Index_Switch = 0;
|
|
|
|
printf("Data from Master: ");
|
|
for(int i = 0; i < LIN_NB_Switch; i++)
|
|
{
|
|
printf("%02X, ", Buffer_Switch[i]);
|
|
}
|
|
printf("\n\n");
|
|
}
|
|
}
|
|
}
|
|
|
|
|
|
void USART0_Handler(void)
|
|
{
|
|
if(USART_INTStat(USART0, USART_IT_LIN_ID)) // ID 已接收
|
|
{
|
|
if(USART0->LINID == LIN_ID_Sensor)
|
|
{
|
|
USART_LINResponse(USART0, USART_LIN_PUBLISH, LIN_NB_Sensor, USART_CHECKSUM_LIN13); // 传感器发送采集数据
|
|
|
|
USART_INTEn(USART0, USART_IT_TX_RDY);
|
|
|
|
Index_Sensor = 0;
|
|
}
|
|
else if(USART0->LINID == LIN_ID_Switch)
|
|
{
|
|
USART_LINResponse(USART0, USART_LIN_SUBSCRIBE, LIN_NB_Switch, USART_CHECKSUM_LIN13); // 开关接收指令数据
|
|
|
|
Index_Switch = 0;
|
|
}
|
|
else
|
|
{
|
|
USART_LINResponse(USART0, USART_LIN_IGNORE, 0, 0);
|
|
}
|
|
}
|
|
|
|
if(USART_INTStat(USART0, USART_IT_RX_RDY))
|
|
{
|
|
uint8_t chr = USART_Read(USART0);
|
|
|
|
if(Index_Switch < LIN_NB_Switch)
|
|
Buffer_Switch[Index_Switch++] = chr;
|
|
|
|
}
|
|
else if(USART_INTStat(USART0, USART_IT_RX_TO))
|
|
{
|
|
}
|
|
|
|
if(USART_INTStat(USART0, USART_IT_TX_RDY))
|
|
{
|
|
if(Index_Sensor < LIN_NB_Sensor)
|
|
USART_Write(USART0, Buffer_Sensor[Index_Sensor++]);
|
|
else
|
|
USART_INTDis(USART0, USART_IT_TX_RDY);
|
|
}
|
|
|
|
if(USART_INTStat(USART0, USART_IT_LIN_DONE))
|
|
{
|
|
}
|
|
|
|
USART_INTClr(USART0, USART_IT_RX_TO | USART_IT_LIN_ID | USART_IT_LIN_DONE);
|
|
}
|
|
|
|
|
|
void SerialInit(void)
|
|
{
|
|
UART_InitStructure UART_initStruct;
|
|
|
|
PORT_Init(PORTA, PIN0, PORTA_PIN0_UART0_RX, 1); //GPIOA.0配置为UART0 RXD
|
|
PORT_Init(PORTA, PIN1, PORTA_PIN1_UART0_TX, 0); //GPIOA.1配置为UART0 TXD
|
|
|
|
UART_initStruct.Baudrate = 57600;
|
|
UART_initStruct.DataBits = UART_DATA_8BIT;
|
|
UART_initStruct.Parity = UART_PARITY_NONE;
|
|
UART_initStruct.StopBits = UART_STOP_1BIT;
|
|
UART_initStruct.RXThreshold = 3;
|
|
UART_initStruct.RXThresholdIEn = 0;
|
|
UART_initStruct.TXThreshold = 3;
|
|
UART_initStruct.TXThresholdIEn = 0;
|
|
UART_initStruct.TimeoutTime = 10;
|
|
UART_initStruct.TimeoutIEn = 0;
|
|
UART_Init(UART0, &UART_initStruct);
|
|
UART_Open(UART0);
|
|
}
|
|
|
|
/******************************************************************************************************************************************
|
|
* 函数名称: fputc()
|
|
* 功能说明: printf()使用此函数完成实际的串口打印动作
|
|
* 输 入: int ch 要打印的字符
|
|
* FILE *f 文件句柄
|
|
* 输 出: 无
|
|
* 注意事项: 无
|
|
******************************************************************************************************************************************/
|
|
int fputc(int ch, FILE *f)
|
|
{
|
|
UART_WriteByte(UART0, ch);
|
|
|
|
while(UART_IsTXBusy(UART0));
|
|
|
|
return ch;
|
|
}
|