|
|
#include <string.h>
|
|
|
#include "SWM221.h"
|
|
|
|
|
|
|
|
|
#define TX_N 8
|
|
|
#define TX_LEN 32
|
|
|
char TX_Buffer[TX_N][TX_LEN] = {
|
|
|
"TestString\r\n",
|
|
|
"TestString1\r\n",
|
|
|
"TestString12\r\n",
|
|
|
"TestString123\r\n",
|
|
|
"TestString1234\r\n",
|
|
|
"TestString12345\r\n",
|
|
|
"TestString123456\r\n",
|
|
|
"TestString1234567\r\n",
|
|
|
};
|
|
|
char RX_Buffer[TX_LEN] = {0};
|
|
|
|
|
|
|
|
|
void SerialInit(void);
|
|
|
|
|
|
int main(void)
|
|
|
{
|
|
|
DMA_InitStructure DMA_initStruct;
|
|
|
|
|
|
SystemInit();
|
|
|
|
|
|
SerialInit();
|
|
|
|
|
|
DMA_initStruct.Mode = DMA_MODE_SINGLE;
|
|
|
DMA_initStruct.Unit = DMA_UNIT_BYTE;
|
|
|
DMA_initStruct.Count = strlen(TX_Buffer[0]);
|
|
|
DMA_initStruct.MemoryAddr = (uint32_t)TX_Buffer[0];
|
|
|
DMA_initStruct.MemoryAddrInc = 1;
|
|
|
DMA_initStruct.PeripheralAddr = (uint32_t)RX_Buffer;
|
|
|
DMA_initStruct.PeripheralAddrInc = 1;
|
|
|
DMA_initStruct.Handshake = DMA_HS_NO; // 无握手信号，适用于 Memory to Memory 传输，MemoryAddr 用作源地址，PeripheralAddr 用作目的地址
|
|
|
DMA_initStruct.Priority = DMA_PRI_LOW;
|
|
|
DMA_initStruct.INTEn = 0;
|
|
|
DMA_CH_Init(DMA_CH0, &DMA_initStruct);
|
|
|
|
|
|
for(int i = 0; i < TX_N; i++)
|
|
|
{
|
|
|
DMA_CH_SetAddrAndCount(DMA_CH0, (uint32_t)TX_Buffer[i], strlen(TX_Buffer[i]));
|
|
|
|
|
|
DMA_CH_Open(DMA_CH0);
|
|
|
|
|
|
while(DMA_CH_INTStat(DMA_CH0, DMA_IT_DONE) == 0) __NOP();
|
|
|
DMA_CH_INTClr(DMA_CH0, DMA_IT_DONE);
|
|
|
|
|
|
printf("RX_Buffer: %s\n", RX_Buffer);
|
|
|
}
|
|
|
|
|
|
while(1==1)
|
|
|
{
|
|
|
}
|
|
|
}
|
|
|
|
|
|
|
|
|
void SerialInit(void)
|
|
|
{
|
|
|
UART_InitStructure UART_initStruct;
|
|
|
|
|
|
PORT_Init(PORTA, PIN0, PORTA_PIN0_UART0_RX, 1); //GPIOA.0配置为UART0 RXD
|
|
|
PORT_Init(PORTA, PIN1, PORTA_PIN1_UART0_TX, 0); //GPIOA.1配置为UART0 TXD
|
|
|
|
|
|
UART_initStruct.Baudrate = 57600;
|
|
|
UART_initStruct.DataBits = UART_DATA_8BIT;
|
|
|
UART_initStruct.Parity = UART_PARITY_NONE;
|
|
|
UART_initStruct.StopBits = UART_STOP_1BIT;
|
|
|
UART_initStruct.RXThreshold = 3;
|
|
|
UART_initStruct.RXThresholdIEn = 0;
|
|
|
UART_initStruct.TXThreshold = 3;
|
|
|
UART_initStruct.TXThresholdIEn = 0;
|
|
|
UART_initStruct.TimeoutTime = 10;
|
|
|
UART_initStruct.TimeoutIEn = 0;
|
|
|
UART_Init(UART0, &UART_initStruct);
|
|
|
UART_Open(UART0);
|
|
|
}
|
|
|
|
|
|
/******************************************************************************************************************************************
|
|
|
* 函数名称: fputc()
|
|
|
* 功能说明: printf()使用此函数完成实际的串口打印动作
|
|
|
* 输 入: int ch 要打印的字符
|
|
|
* FILE *f 文件句柄
|
|
|
* 输 出: 无
|
|
|
* 注意事项: 无
|
|
|
******************************************************************************************************************************************/
|
|
|
int fputc(int ch, FILE *f)
|
|
|
{
|
|
|
UART_WriteByte(UART0, ch);
|
|
|
|
|
|
while(UART_IsTXBusy(UART0));
|
|
|
|
|
|
return ch;
|
|
|
}
|